2 x Gigabit Ethernet + RS-232/RS-485 over Single Fiber - Full Duplex Fiber Converter
GIGABIT ETHERNET And RS-232 and RS-485 over single fiber Transceiver
Thor Fiber Multi-Serial (RS-232 / RS-485) + 2 x RJ45 Fiber Optic Converters that transmit a serial protocol over fiber with 2 ports for Ethernet transport.
These units support single-mode and come with SC/PC connectors. The serial port interface is a terminal block connector field wiring.
These units automatically detect the signal baud rate of the connected serial device that ranges from 300bps to 115.2Kbps baud. It also automatically adjusts to changes in the connected device’s bound during operation without reconfiguration or interruption of service.
This unit utilizes WDM optical multiplexing technology. Side A is equipped with a 1310nm transmitter, and Side B with a 11550nm transmitter. A complete setup requires both A and B units (sold as a pair).
Point-to-Point Bi-Directional Transmission
-
Zero-Delay Automatic Forwarding
-
Transmission over Single (Simplex) Fiber
-
Supports 2 Ports 10/100/1000 Gigabit Ethernet (10BASE-T / 100BASE-TX / 1000BASE-T)
-
2 x RJ45 Connectors (Managed)
-
RS-232 and RS-485 to Fiber with Automatic Baud Rate Detection
-
Baud Rate: 300bps to 115.2Kbps
-
Protocol: Asynchronous Serial
-
Supports Single-Mode, Single-Fiber with SC Connectors (Simplex)
-
Distance: 20Km standard (40, 80, or 120Km available – model dependent)
-
Hot-Pluggable
-
Mounting Options: Chassis available, Wall-mounted, or DIN-Rail installation
-
Protection: 1500W Surge Protection, 15KV ESD Protection
-
Power Supply: External
-
Operating Temperature: -40°C to +70°C
-
Input Voltage: 9 ~ 48VDC
-
Reverse Polarity Protection
-
Compact Form Factor
EMI, RFI and Transient Surge Immunity
Electromagnetic interference (EMI) is a common phenomenon in typical environments like industrial plants, warehouses and factory floors. This interference can cause corruption of data over serial or copper-based Ethernet links. Data transmitted over fiber optic cable however is completely immune to this type of noise, thus preventing the negative effects of voltage equalization currents and electromagnetic interference on the data cables. A Serial to Fiber Media Converter therefore enables you to inter-connect your serial devices over fiber ensuring optimal data transmission, increased availability of the system, and improved network design.
Simplex fiber solution - A complete setup requires both A and B units (sold as a pair) - 20Km over single mode fiber
F-2GET-RS-A/B (A/B Link)
F-2GET-RS-A (A unit) 2 x Gigabit -10/100/1000 Ethernet + RS485 + RS 232 over 1 fiber transceiver fiber SC/PC connector -20Km (1310nm -TX, RX- 15510nm)
F-2GET-RS-B (B unit) 2 x Gigabit - 10/100/1000 Ethernet + RS485 + RS 232 over 1 fiber transceiver fiber SC/PC connector -20Km (1550nm -TX, RX-1310nm )
XX - Other Optical Distance - 40, 80, 120Km
Physical and Data Link Layer Standards:
|
10/100/10000 Ethernet -2 x RJ 45 ports (G1 and G2)
|
|
RS data Physical interface |
The industry standard - Copper Terminal Block |
|
Interface Signal |
RS-232 RS-485 |
|
Baud Rate |
.Serial port data transparent transmission,baud rate up to 520 kbps |
|
Code Bit Rate |
0-1Mbps Typically |
|
BER |
< 10 -9 |
|
Protocol |
Asynchronous Serial |
| Mode | Point to point Bi-directional full duplex |
|
Optical |
|
|
Fiber Connector |
SC/PC- Simlex (SFP stile) |
|
Optical distance |
20Km (40,80,120km -model dependent ) |
|
Fiber type |
Single-mode, Simlex (Dual fiber SFP avaiable) |
|
LED Indicators |
PWR, TxD, RxD |
|
RS-232 signal |
IN, OUT, GND |
|
4-wire RS485 Signal |
T+, T-, R+, R-, GND |
|
2-wire RS485 Signal |
D+, D-, GND |
|
RS-422 signal |
T+, T-, R+, R-, GND ( special order) |
|
Interface protection |
1500W surge protection and 15KV ESD protection |
|
Environmental temperature |
-30 to +75C |
|
Relative humidity |
0-95% ( no condensation) |
|
RoHS Compliant |
Yes |
|
Power supply voltage |
AC 85-220V |
|
Power Consumption |
2.68W |
|
Power Input |
5V DC |
Dimensions : 4"x5"x1.25"